Calibration      :  
                    Run 1 attributes in CDFDB$A_SUM area
                    ACM,AMR,ANM,ASP,AST,BET,CAT,CNM,COR,CSO,DRV,DVC,EII,
                    ELB,ENG,EQI,FAP,FAT,FLS,G87,GAI,GGM,GGP,GTL,HVR,HVS,
                    LDR,LED,LER,LGR,LSP,LSR,LTR,MAP,MER,MXB,PDD,PED,PIB,
                    PRO,PUD,QDR,QER,QNM,RBC,RCO,RWG,SCL,SLR,SLU,SRC,SWR,
                    TDC,THR,TMS,TRC,TRG,XEF,
                    Definition of Run 1 Attributes (39 out of 58) from CDFDB$CMS 
                    CALIB_DATA_STRUCTURES.RNO last modified Oct 1987, also 
                    available in c$doc:CALI_DAB_STRUCT.MEM (CDF 501 unreleased).
                    AMR :- Amerishium source calibration
                    ASP :- ASD pre-amplifier pulse calibration,  units counts, time/count
                    AST :- ASD Test pulse calibration,   units counts, time/count
                    CAT :- Lecroy CAT Module calibration,   units counts, time/count
                    CNM :- Nominal Charge Injection Gain (fC/volt)
                    DRV :- Drift time correction constants
                    EII :- Current Channel amplifier gain  nA/count
                    ELB :- Calorimeter Electron Beam calibration. fC/Gev/nA
                    ENG :- Nominal energy scale , units  fCoulomb/Gev
                    EQI :- QVC Channel amplifier gain,   units fCoulomb/count / QNM
                    GAI :- Electronics gain (Channel type depenedent units)
                    HVR :- High voltage readback file
                    HVS :- High voltage set file
                    INM :- Nominal Current Channel Gain  (nAmp/count)
                    LDR :- Linear Distance Response Coefficient (cm/count/SCL
                    LED :- Central Wedge LED calibration,  units fCoulomb
                    LER :- Linear Energy Response coefficient (Gev/count/SCL)
                    LGR :- Linear General Response Coefficient ( response/count/SCL)
                    LSP :- Laser calibration
                    LSR :- Central wedge laser calibration,  units fCoulomb
                    LTR :- Linear Time Response Coefficient (nsec/count/SCL)
                    MAP :- Detector response map
                    MXB :- MX constants used (alpha,beta, pDAC, tDAC) - I*2 bank
                    PDC :- Cosmic Ray Gate Pedestals (counts)
                    PED :- QVC Channel pedestal run,   units counts
                    PIB :- Calorimeter Pion Beam Calibration fC/Gev/nA
                    PRO :- Channel status (amplifier status, fiber status etc.)
                    QDR :- Quadratic Distance Response Coefficient (R*4)
                    QER :- Quadratic Energy Response coefficient (R*4)
                    QNM :- Nominal electronics gains (fC/Count; nsec/Count;)
                    RBC :- Rabbit calibrations, ADC vs PED, ADC vs THR Vcal.
                    SCL :- Normalisation scale (== QNM/ENG)
                    SRC :- QVC Channel source calibration,  units nA (Scintillator)
                    TDC :- Photo-tube TDC constants
                    THR :- QVC Channel threshold, units  counts
                    TMS :- Tracking Global time scale & offset, units time/count, counts
                    TRC :- Trigger calibration constants (CAS)
                    TRG :- Trigger calibration constants (RAW)
                    XEF :- Central wedge Xenon Flasher calibration,  units fCoulomb
 


Trigger          :  
                    In run 1 there was only one attribute L12 in 
                    CDFDB$K_PRM area

Run Conditions   :  
                    In Run 1 the attributes were ACL, DLG, L03, L12, MXB, POT,
                    RNC, TFM. 
                    MXB :- MX constants used (alpha,beta, pDAC, tDAC) - I*2 bank
                  

CDF Conditions   :  In run 1 J. Patrick says these contained slow controls info.
                    This database appears to contain info not acquired by 
                    a run_control calibration run, but obtained by other means.
                    In run 1 these databases contained lists of dead layers,
                    dead channels, pedestal shifts, gas gain, and other 
                    miscellaneous info in CDFDB$H_PRM
                    Run 1 attributes ACM, AVB, AVE, AVH, BPO, BRN, CTL, 
                    DED, DOA, DVC, GGQ, GGR, GGS, LTB, LTE, LTH, MAP, PMD,
                    PSF, SVB, SVE, SVH, UTB, UTE, UTH, WPO.
                    PSF :- Pedestal Shift
                    DED :- Dead Channel
                    GGQ :- Gas Gain Calibration 
                    GGR :- Gas Gain Calibration
                    GGS :- Gas Gain Calibration
                    Some are constants determined asyncrhonously from the
                    run number, and then assigned to the run number 

Geometry         :  In Run 1 there was a CDFDB "Geometry" database in 
                    CDFDB$B_PRM containting the following attributes 
                    ACM,AL1,AL2,AL3,AL4,CAP,DVC,FS1,FS2,FS3,FS4,SU1,SU2,
                    SU3,SU4

SVX               :  In Run 1 there was a special SVX Cailb database with the 
                     following attributes in CDFDB$F_SUM
                     EFF,GCQ,GND,GNQ, LEA,PCQ,PDD,PDQ,PED,THR,